VADDIO WALLVIEW PRO EAGLEEYE Manuel d'utilisateur télécharger pdf (Page 11)

Call 800-572-2011

Toll Free

vaddio.com

Presenter-Controlled Camera Systems

Vaddio’s Presenter-Controlled Camera Systems include the TrackVIEW and the ControlVIEW

™

Xtreme. They represent

unique approaches to camera control in presentation and video classroom environments.

The TrackVIEW Camera Control System

This system is designed to provide system integrators with an easy-

to-operate, fully featured, multiple-mode camera tracking system. The

TrackVIEW is a presenter control system that incorporates both motion-

based camera tracking and camera preset tracking in one system and has

many unique features that enhance the automatic aspects of presenter-

activated control systems.

The TrackVIEW was designed as a two camera system; one camera is the

reference camera which is framed on the whole presentation area and

the second camera is the tracking camera which responds to presenter

movement within the reference area. The TrackVIEW was designed to

use two PTZ cameras.

The Sony EVI-D70 is used for the reference camera and the tracking

camera can be the EVI-D70, EVI-D100 or the EVI-HD1. Cameras for

the TrackVIEW system are equipped with the Vaddio EZCamera Cabling

System for Cat. 5 connectivity.

The TrackVIEW can track to presets with triggers like the StepVIEW Mats

or AutoVIEW IR Sensor, and when triggers are not tracking to presets, the

TrackVIEW can track motion, allowing the presenter to stay on-camera

as they walk between preset camera shots.

The TrackVIEW module has the EZCamera

™

system built-in (PowerRite

camera power supply and Quick-Connect break out box) and provides

power to, and returns video from, the EVI-D100 and EVI-D70 over a single

Cat. 5 cable. RS-232 originates from the TrackVIEW Module as well and

uses the EZCamera system with Cat. 5 connectivity.

Other features include ﬁrst step/last step and multi-step modes for

programming the preset triggers for priority and for multi-trigger wide

shots and a USB port for setting up the TrackVIEW system software.

The ControlVIEW Xtreme PTZ Camera Control System

This system is designed to control up to four PTZ cameras and assign up

to 72

total system camera preset positions to any of the four cameras.

The ControlVIEW Xtreme works with any VISCA controllable PTZ camera

and has automatic camera detection and control configuration. The

ControlVIEW Xtreme responds to input triggers from the TouchVIEW

buttons, StepVIEW Mats, AutoVIEW IR Sensors and MicVIEW

™

automatic

microphone switcher/mixer as well as many other contact closure devices.

Any of the 72 input triggers can be programmed to go to any one of the

four PTZ cameras attached and to a unique pan/tilt/zoom camera position

as well. The ControlVIEW Xtreme works very well in the videoconferencing

classroom environment.

Firmware revision 1.65 has added a Polycom and TANDBERG codec mode

that essentially takes any input trigger like the MicVIEW and translates the

RS-232 output of the ControlVIEW Xtreme to the preset RS-232 codes of

the codec, allowing any trigger to change the presets on the codec.

The ControlVIEW Xtreme was designed to be very easy to install and is

ideal for use in a video classroom where automatic camera control must

be transparent and easy to use.

ControlVIEW Xtreme - Basic System Conﬁguration

TrackVIEW – Basic System Conﬁguration

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 35 36

Commentaires sur ces manuels

Pas de commentaire

VADDIO WALLVIEW PRO EAGLEEYE Manuel d'utilisateur Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Caméras de sécurité VADDIO WALLVIEW PRO EAGLEEYE