Vaddio Quick-Connect 4 Manuel d'utilisateur télécharger pdf

Installation and User Guide

Camera and Electronic Products for Integrators

Vaddio Quick-Connect 4 - Document 341-256-1 Rev C

Quick-Connect™ 4

Video, Power and Control Wiring Center

INTRODUCTION

The Vaddio™ Quick-Connect 4, Video, Power and Control Wiring Center (Figure 1)

simplifies Operator and Presenter camera systems using the Vaddio EZCamera™

Cabling standard. The Quick-Connect 4 can accommodate up to four separate

Vaddio PTZ cameras, combining and consolidating four Vaddio Quick-Connect

Boxes, four PowerRite™ power supplies and four EZCamera Control Adapters used

with the EZCamera cable system.

Each camera port has an individual 18VDC supply to power a single PTZ camera.

Power is provided to the camera and S-Video and Composite video are both

returned to the Quick-Connect 4 on the same single Cat. 5 cable for Power/Video.

Individual control ports are supplied for camera control systems like the

ProductionVIEW™ and camera control daisy chaining is accommodated through the

first camera control port as well.

Control inputs are either DB-9 or RJ-45 and control outputs are RJ-45, which

connect easily with all Vaddio WallVIEW™, CeilingVIEW™, EZCamera and

HideAway series cameras.

INTENDED USE

Before operating the Vaddio Quick-Connect 4, please read the entire manual

thoroughly. The wiring system was designed, built and tested for use indoors.

Outdoor operation is not recommended, has not been tested and could damage the

unit and/or create a potentially unsafe operating condition. Use only the Vaddio

provided power supply.

SAVE THESE

INSTRUCTIONS

The information contained in this manual will help you install and operate your

Vaddio Quick-Connect 4. For reference, Vaddio keeps copies of Specifications,

Installation and User Guides and most pertinent product drawings for the Vaddio

product line on the website. These documents can be downloaded from

www.vaddio.com

free of charge.

IMPORTANT

SAFEGUARDS

Read and understand all instructions before using. Do not operate the device if it

has been dropped or damaged. In this case, a Vaddio technician must examine the

product before operating. To reduce the risk of electric shock, do not immerse in

water or other liquids and avoid extremely humid conditions.

Figure 1:

Vaddio Quick-Connect 4

Video, Power and Control

Wiring Center

Front Panel (above) and

Back Panel (below) shown

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - Quick-Connect™ 4

Installation and User Guide Camera and Electronic Products for Integrators Vaddio Quick-Connect 4 - Document 341-256-1 Rev C Quick-Connect™ 4 Vide

Page 2

Quick-Connect 4 Vaddio Quick-Connect 4 - Document 341-256-1 Rev C Page 2 of 8 UNPACKING Carefully remove the device and all of the parts from t

Page 3

Quick-Connect 4 Vaddio Quick-Connect 4 - Document 341-256-1 Rev C Page 3 of 8 BASIC CAMERA CONNECTION 4-Camera Daisy

Page 4

Quick-Connect 4 Vaddio Quick-Connect 4 - Document 341-256-1 Rev C Page 4 of 8 4-Camera Direct Control Example (4-Control Ports) ProductionVIEW &

Page 5 - Video/Power Connection RJ-45

Quick-Connect 4 Vaddio Quick-Connect 4 - Document 341-256-1 Rev C Page 5 of 8 4-Camera Quick-Connect 4 Head End Daisy Chain Example Detail Note: Ca

Page 6 - 5 1

Quick-Connect 4 Vaddio Quick-Connect 4 - Document 341-256-1 Rev C Page 6 of 8 Control Inputs Control Input Connections RJ-45 and DB-9F RJ-45 Pins 1)

Page 7

Quick-Connect 4 Vaddio Quick-Connect 4 - Document 341-256-1 Rev C Page 7 of 8 GENERAL SPECIFICATIONS Camera Ports: 4-Individual RS-232 Control Thr

Page 8

Quick-Connect 4 Vaddio Quick-Connect 4 - Document 341-256-1 Rev C Page 8 of 8 9433 Science Center Drive, New Hop

Commentaires sur ces manuels

Pas de commentaire

Vaddio Quick-Connect 4 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Vaddio Quick-Connect 4. Vaddio Quick-Connect 4 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Vaddio Quick-Connect 4